• Make a perpendicular cut across the tail and lift the fillet away
• Turn the salmon over and insert the knife where the head used to be, just above the backbone
• Use the same technique to saw through the ribs and remove the meat from the spine, creating a second fillet
• When you reach the tail, cut the fillet away from the body
• Lay the fillet skin side down on the cutting board Insert the fillet knife just underneath the first few ribs
• Slowly work the knife under the ribs, angling it toward the thicker part of the fish and toward the tail, to loosen a thin flap of meat containing the ribs
• Continue until you have removed the ribs, discard the flap
• Do not cut into the ribs too deeply, or you will lose too much meat
• Cut as closely underneath the ribs as possible, so you only remove a thin layer of meat attached to them
• Repeat with the second fillet
• Extract the remaining small rib bones near the tail end of the fillet with needle-nosed pliers
• Trim the edges of fatty tissue from the filet’s belly meat
• Some consider this portion of the meat to be too strong in taste Simply slice it off and discard
• Rinse the fillets in standing cold water
• Salt may be added to remove superficial impurities from the meat
• Store the meat in a refrigerator
• Do not let the meat sit out for too long, or it will spoil
• You can also freeze the meat in freezer bags for up to six months
• Prepare the salmon fillets as desired for cooking The backbone and head may be saved to make a broth for soup or risotto
• Put the fish trimmings, entrails, and carcass in a tied-off plastic bag and toss in the rubbish
Process:
• Place the fish on its side on a large cutting board
• Hold the tail down with one hand, and with the other insert a fillet knife into the vent, or the anus, located on the underside of the fish near the tail
• Pull the knife from the vent along the belly toward the head and stop just between the gills
• Make sure you are using a sharp knife to make the cut You should not have to make a sawing motion; the cut should be clean
• Take care not to cut deep into the vent or belly, since the organs inside may contain bacteria that could contaminate the fish If your initial cut is too shallow, you can go back and make a deeper cut
• If you do cut into the organs, rise the liquid off immediately
• Make sure it flows out of the fish, rather than deeper inside
• Make a cut from the fish's back to its belly
• Start at the backbone above the pectoral fin
• Press your knife down until you can feel the spine, and make a downward cut that extends behind the fin and ends at the belly
• Do not cut deeply since you want to avoid damaging the organs
• Lift the meat to make sure it is detached from the head area
• You should be able to lift a flap from the side of the fish If it is still attached to the head, use the knife to cut it away
• Turn the fish around and make a cut from the fish's belly to its back, start the cut at the bellow below the pectoral fin
• Since you are coming at it from the other side, extend the cut in front of the fin and end it at the backbone Lift the flap of meat to make sure it is no longer attached to the head
• Place the salmon on its belly and cut off the head Use a heavier, sharper knife, rather than the fillet knife, to make a cut straight through the background just behind the head
• The intestine will still be attached to the vent
• Use your knife to cut it cleanly
• The head, internal organs, and pectoral should come off in one piece, and discard them
• A serrated knife makes it easier to cut through the backbone
• The dark red organ along the salmon's backbone is its kidney
• Use the fillet knife to carefully cut it away and lift it from the fish
• Use a large knife (preferably serrated) to saw off the dorsal and caudal fins, then discard them
• With the salmon resting on its side, insert the fillet knife at the end where the head used to be, just above the backbone
• Begin using a gentle sawing motion to cut through the ribs and separate the meat from the contoured spine
• Do not cut too far away from the backbone since you want to preserve as much meat as possible in the fillet
• Cut until you reach the tail
MR HANS
Preparing a Whole Salmon
View / Download or Print a PDF version from here
Go to next column
